Suitable for selected Australian-market vehicles using 6x114.3 PCD, approx. 66.1mm centre bore and M12x1.25 wheel studs.

The fitment table below is a guide only. Please verify your exact vehicle specifications before ordering.

The following models may share similar 6x114.3 / 66.1 / M12x1.25 wheel specifications, but they are not common Australian-delivered vehicles. Please verify carefully before purchase.

• Model: WS-G-6-114.3/25MM(66.1 / M12x1.25)
• Quantity: 4 Pieces
• Spacer Thickness: 25mm Each
• Vehicle-Side PCD: 6x114.3
• Wheel-Side PCD: 6x114.3
• Centre Bore: 66.1mm
• Stud Thread: M12x1.25
• Mounting Type: Bolt-On Stud Type
• Design: Non-Hubcentric / Lug-Centric
• Finish: Black

• 4 × 25mm Non-Hubcentric Wheel Spacers
• 24 × M12x1.25 Nuts

Only the items shown and listed are included.

Please verify all of the following before purchase:

• Your vehicle PCD is exactly 6x114.3.
• Your vehicle centre hub is suitable for a 66.1mm centre bore spacer.
• Your original wheel stud thread is M12x1.25.
• Your wheels also use a compatible 6x114.3 stud pattern.
• Your wheel centre bore and rear mounting pad are suitable.
• The back of the wheel has enough recess clearance if original studs protrude past the spacer face.
• There is enough guard, brake, suspension and tyre clearance after adding 25mm per side.
• The spacer sits completely flush against the hub.
• The wheel sits completely flush against the spacer.

Wheel spacers are safety-critical components. Incorrect fitment or installation may cause vibration, wheel loosening, bearing stress, tyre contact, handling issues or serious vehicle damage.

• Professional installation is strongly recommended.
• This is a Non-Hubcentric / Lug-Centric spacer and does not have a raised centre locating lip.
• Do not install if the PCD, centre bore, stud thread or wheel clearance does not match correctly.
• The spacer must sit completely flat against the vehicle hub.
• The wheel must sit completely flat against the spacer before tightening.
• Original wheel studs may extend beyond the face of the 25mm spacer on some setups.
• The back of the wheel must have sufficient recesses to clear the original studs if they protrude.
• Check brake caliper, suspension, guard and tyre clearance before driving.
• Do not stack wheel spacers.
• Use the correct torque specification for your vehicle and wheels.
• Re-torque all nuts after 50–100km of driving and inspect regularly.
• Check local road regulations before use, as wheel spacer legality may vary by state or territory.
• The buyer and installer are responsible for confirming safe and legal fitment before use.

• Vehicles using 6x139.7 PCD, including many Hilux, Ranger, BT-50, Triton, D-Max and Patrol models.
• Nissan Navara D22 models using 6x139.7 PCD.
• Nissan Pathfinder R52 models.
• Vehicles using any PCD other than 6x114.3.
• Vehicles with centre hub larger than 66.1mm.
• Vehicles using a wheel stud thread other than M12x1.25.
• Any wheel without enough rear recess clearance if original studs protrude.
• Any setup where the spacer or wheel cannot sit completely flush.
• Any vehicle where 25mm extra width causes tyre, guard, brake or suspension contact.

1. Confirm your vehicle is 6x114.3 and uses M12x1.25 wheel studs.
2. Confirm the vehicle centre hub is suitable for the 66.1mm spacer centre bore.
3. Clean the vehicle hub mounting surface thoroughly.
4. Position the spacer against the hub.
5. Confirm that the spacer sits completely flat against the hub.
6. Install the supplied M12x1.25 mounting nuts.
7. Tighten gradually using a diagonal / star pattern.
8. Confirm original studs do not interfere with the back of the wheel.
9. Install the wheel onto the spacer studs.
10. Tighten all wheel nuts to the correct torque specification.
11. Recheck and re-torque all fasteners after approximately 50–100km.

Is this listing for 4 spacers?
Yes. This listing includes 4 wheel spacers and 24 M12x1.25 nuts.

Are these hubcentric?
No. These are Non-Hubcentric / Lug-Centric wheel spacers and do not have a raised centre locating lip.

Will these fit Nissan Navara D40 / D23?
They are designed for selected D40 and D23 models using 6x114.3, approx. 66.1mm centre bore and M12x1.25 studs.

Will these fit Mercedes-Benz X-Class?
They may suit selected X-Class W470 models using the same 6x114.3 / approx. 66.1mm / M12x1.25 specification. Please confirm wheel and brake clearance before ordering.

Will these fit Nissan Pathfinder?
They suit selected Pathfinder R51 models only. They are not suitable for Pathfinder R52 models.

Will these fit 6x139.7 vehicles?
No. These are 6x114.3 spacers and will not fit 6x139.7 vehicles.

Can I install them on the front and rear?
Yes, only if your vehicle, wheels, brakes, suspension and guard clearance are suitable for 25mm spacers.

Are these PCD adapters?
No. These are straight 6x114.3 to 6x114.3 wheel spacers and do not convert the stud pattern.

Can I stack these with another spacer?
No. Wheel spacers must never be stacked.

Do they need to be re-torqued?
Yes. All fasteners should be checked and re-torqued after approximately 50–100km and inspected regularly afterwards.

This product is covered against manufacturing defects under our applicable warranty policy.

The warranty does not cover incorrect fitment, improper installation, incorrect torque, vibration caused by lug-centric installation, impact damage, motorsport use, vehicle modification, stacked spacers, wheel clearance issues, legal compliance issues or normal wear and tear.

Fast Dispatch: Orders are generally processed and dispatched within 24–48 business hours.

Inspect Before Installation: Please check all measurements and inspect the product before installation.

Returns: Products that have been installed, marked, modified or damaged may not be eligible for change-of-mind return.

Please contact our customer service team before returning an item to confirm eligibility and receive return instructions.