Low-profile coverage
Clean OEM-style finish
A sleek tri-fold hard lid profile gives your ute a refined, practical finish while helping protect cargo from the weather.
Skip to product information
YARA Alloy Tri-Fold Hard Lid Tonneau Tub Cover for GWM Cannon 2020-2025
$589.00
Sale ends in
--:--:--
—
Pickup available at Yara Auto Parts
Usually ready in 24 hours
Large-item delivery
Estimate shipping
Enter your postcode for an estimated Tri-Fold Hard Lid delivery rate, including applicable remote-area surcharges.
Recommended
Free store pickup — save on shipping
Large items are expensive to freight, so we highly recommend free collection from our Banksmeadow store.
Yara Auto Parts
U6/11 Julian Cl, Banksmeadow NSW 2019
Select Pick up at checkout. We will notify you when your order is ready.
View standard state rates
| State | Standard rate | Remote-area policy |
|---|---|---|
| NSW | $80 | No surcharge |
| ACT | $90 | No surcharge |
| VIC | $110 | No surcharge |
| QLD | $125 | +$100 |
| SA | $120 | +$100 |
| WA | $125 | +$100 |
| TAS | $200 | +$100 |
| NT | $350 | +$100 |
Estimates are for guidance only. Remote depots, islands, PO boxes and unusually difficult delivery addresses may cost more. We will confirm any adjustment before dispatch.
YARA AUTO PARTS / PRODUCT INFORMATION
Product Details
The essentials to check before choosing your Tri-Fold Hard Lid.
Vehicle compatibilityYARA Alloy Tri-Fold Hard Lid Tonneau Tub Cover for GWM Cannon 2020-2025
Cover typeHard Tri-Fold Tonneau Cover
ConstructionAluminium hard panels
FinishBlack, low-profile design
Key Features
- Three-panel folding design for convenient everyday tub access.
- Rigid aluminium panels with a clean, low-profile finish.
- Weather-resistant sealing helps reduce water and dust entry; not fully waterproof or dustproof.
- The complete lid can be removed when full tub access is needed, subject to the supplied fitting system.
Fitment & Installation
The mounting bracket must be installed onto the tub first. Installing this bracket requires drilling holes in the tub. The lid is then secured to the installed bracket using clamps. Please review the Important Note and installation images below before purchasing.
Check before ordering: Sports bars, headboards, tub racks and aftermarket tub accessories may affect fitment. Please contact us with photos if your ute has accessories fitted.
Full Product Description & Installation Images
Original product information is displayed in full, including the Important Note, bracket diagrams and any product-specific fitting instructions.
TRI-FOLD HARD TONNEAU COVER ALUMINIUM
GWM Cannon Dual Cab | 2020 – Onwards | Heavy Duty Protection
GWM Cannon
2020 – Onwards
Aluminium Alloy
Tri-Fold Design
Lockable Security
Vehicle-Specific Fitment
Weatherproof Seals
Product Overview
Vehicle
GWM Cannon
Body Type
Dual Cab Only
Material
Aluminium Alloy
Lid Type
Hard Tri-Fold
Finish
Matte Black Powder
Installation
Bracket & Clamp Fitment (Drilling May Be Required)
Why Upgrade to Hard Lid
Feature
✦ Ours (Hard)
Soft Covers
Security
✔ Theft-Proof Aluminium
✘ Easily cut with knife
Waterproof
✔ Heavy Duty Rubber Seals
✘ Prone to pooling/leaks
Durability
✔ Rigid Powder-Coated Metal
✘ Vinyl stretches/fades
Fuel Economy
✔ Aerodynamic Flat Profile
✘ Wind flap at high speed
⚠️ Ultimate Security for your GWM Cannon
Protect your expensive tools and gear from theft and the elements. This Aluminium Hard Tri-Fold Lid is engineered specifically for the GWM Cannon Dual Cab tub. When your tailgate is locked, the lid cannot be opened, turning your tub into a secure trunk.
Key Features
01
Heavy Duty Aluminium
High-grade honeycomb aluminium alloy panels are lightweight yet incredibly strong. Can support significant weight and resists dents.
02
Full Weather Protection
Features high-quality EPDM rubber seals on all edges to keep rain, dust, and debris out of your tub.
03
Quick Tri-Fold Access
Innovative three-panel design allows you to fold it up for larger loads or keep it fully closed for maximum security.
04
Lockable Design
Secondary locking clips on the underside keep the lid tightly shut. Works in conjunction with your factory locking tailgate.
05
Vehicle-Specific Installation
Simple clamp-on mounting system. Special mounting brackets may be required depending on the tub-rail configuration.
06
Matte Black Finish
Premium textured powder-coat finish provides a sleek look while offering superior scratch and UV resistance.
🔧 Maintenance & Install Tips
- Clean the tub rails thoroughly before fitting for the best seal.
- Ensure the clamps are tightened evenly to maintain a level profile.
- Periodically check the clamp tension, especially after off-road driving.
- When driving with the lid folded open, always use the safety straps provided.
What's in the Box
Included
1 × Aluminium Hard Tri-Fold Lid
Included
Complete Fitting Kit (Clamps)
Included
Weather Seals & Safety Straps
Compatibility
| Make | Model | Series | Years |
|---|---|---|---|
| GWM | Cannon / P-Series | Dual Cab (Only) | 2020 – Onwards |
Fits Cannon, Cannon-L, and Cannon-X models. Will NOT fit single cab models or vehicles with certain aftermarket sports bars/roll bars unless modified.
Important Fitment Note — Special Mounting Brackets May Be Required
Test-fit the cover before drilling. If the supplied clamps cannot engage securely with your tub rails, the supplied special mounting brackets may need to be installed on both sides of the tub, as shown below. Bracket quantity and position may vary by vehicle.
Included mounting kit: The special mounting brackets, bolts and fixing hardware required for this installation are included with the cover. No separate purchase is required.
Installation Steps
- Position the cover: Lay the tri-fold cover flat and square on top of the tub. Align the front, rear and both side edges.
- Locate and mark: From inside the tub, identify where each clamp needs to engage. Hold the supplied special brackets against the corresponding positions on both tub rails and mark the drilling points carefully.
- Remove the cover: Lift the tri-fold cover off the tub before drilling.
- Install the brackets: Before drilling, confirm there are no wiring looms, fuel lines, brake lines or other components behind the marked areas. Drill the marked holes, apply suitable corrosion protection to exposed metal, then bolt the brackets securely to both tub rails.
- Apply the foam sealing tape: Clean and dry the mounting surfaces. Apply the supplied foam tape around all four tub edges, including the tailgate edge. Position the tape so it straddles the tub-rail edge—approximately half on the top horizontal surface and half down the inside vertical surface.
- Refit the cover: Place the tri-fold cover back onto the tub and check the alignment again.
- Secure the clamps: Hook each clamp onto its installed bracket and tighten evenly until the cover is held firmly. Do not overtighten.
- Final safety check: Confirm every bracket, bolt and clamp is secure. Re-check all fasteners after the first short drive and periodically thereafter.
Professional installation is recommended if you are unsure about drilling, bracket placement or clamp tension.
Tri-Fold Hard Lid Features
Built for fast access, secure coverage and everyday ute use
Premium tri-fold coverage with low-profile styling, durable aluminium construction and practical loading flexibility.
Quick access
Open only what you need
Fold back the front panels for quick tub access without removing the whole cover. Ideal for everyday tools, shopping, luggage and work gear.
Flexible loading
Full cargo access when required
The tri-fold design opens wide when you need more tub space, giving you flexibility for taller or bulkier loads.
Aluminium build
Strong panels for daily use
Durable aluminium construction and a tough black finish help the cover stand up to Australian weather and regular work use.
Simple fitment
Designed for straightforward installation
Vehicle-specific fitment and clamp-style mounting make setup cleaner, faster and easier to check before daily use.
Warranty
Drive with confidence. All Yara Auto Parts products, including roller shutters, come with a 12-month voluntary manufacturer warranty against manufacturing defects, in addition to your rights under the Australian Consumer Law.
Independent aftermarket notice: Vehicle manufacturer names, vehicle images, badges and logos are used only to identify compatibility or illustrate fitment. Yara Auto Parts is an independent aftermarket business and is not affiliated with, sponsored by or endorsed by any vehicle manufacturer. All third-party trade marks and logos belong to their respective owners. Products are aftermarket unless expressly stated otherwise. Read our IP & Vehicle Compatibility Disclaimer.
If you need to make a claim or require assistance, our Sydney-based team is ready to help.
View Warranty Policy
Return
Shop with peace of mind. If you change your mind or the item isn't right for you, we offer an easy 30-day return policy for unused products in their original packaging. Our Sydney team makes the process hassle-free.
View Return Policy.
Shipping
Fast, reliable dispatch. Orders are processed from our local Sydney warehouse within 1 business day. We offer competitive flat-rate freight across Australia.
View Shipping Policy
You May Also Like
Explore our latest products.
From our customers
Customer reviews
Feedback for YARA Alloy Tri-Fold Hard Lid Tonneau Tub Cover for GWM Cannon 2020-2025, with each source clearly labelled.
This product · eBay—
Loading positive feedback rate…
Our store · eBay—
Loading positive feedback rate…
Website reviews
Reviews collected through Judge.me
Original ratings, comments and customer photos.
Loading website reviews…
eBay · This product
eBay feedback for this item
Loading matched feedback…
Matched to this exact item using its eBay listing number. eBay feedback is shown as Positive, Neutral or Negative — not converted into a star rating.
Loading eBay feedback…
eBay · Store-wide
More experiences from our eBay customers
These reviews cover different products from our store. They are not reviews of this specific item.
Select this tab to load store feedback.
